- “Sets a temperature and stays cold”
- “Broils but will not bake”
- “A message in words on the display”
Symptom
Viking oven not heating
An oven that sets a temperature and stays cold, or heats on one mode and not another. On this make the message is usually in words rather than in numbers, and RTD ERROR names the sensor outright.
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
Five ordinary causes
What this usually turns out to be
Cheapest and commonest first, which is also the order we check them in. They sit hundreds of dollars apart, and only the unit settles which one is yours.
-
The RTD, which is the oven sensor
With no believable temperature the control will not heat at all. This make publishes it in plain words — RTD ERROR — and it is one of the more affordable repairs here.
Oven element & sensor repair from $195 -
An element open
It heats on one mode and not another, because bake, broil and convection use different elements.
Oven element & sensor repair from $195 -
A relay that will not close
The element is sound and nothing is switching it. That is a control repair rather than an element one.
Control board replacement from $345 -
A thermal cutout that has opened
Something got hot enough to trip it, and asking why is how the same call is avoided twice.
Oven element & sensor repair from $195 -
On a gas range, the oven igniter
It glows long after it has stopped getting hot enough to open the gas valve, which is why an oven of that age lights sometimes and not others.
Sealed burner & igniter repair from $165
In five minutes
Before you call anybody
None of it needs tools, and all of it makes the visit shorter.
-
01
Which modes work
Bake, broil, convection. Different elements, and the answer halves the diagnosis.
-
02
Photograph the message before clearing it
Cutting power loses it. On this make it is a word rather than a code, and the word is the part.
-
03
Listen for the cooling fan
It should be audible above the door while the oven heats. Silence points somewhere quite different from a dead element.
-
04
Check the breaker properly
Off and fully back on. A double-pole breaker can drop one leg and still look set, which leaves a happy display and a cold oven.
How it shows up
What people describe when they call
Two shortcuts
Narrow it down before anybody arrives
A description of the behaviour leaves a few possible causes. A code names the subsystem, and the model number says which parts to bring. Either one shortens the visit; both together usually settle it.
If the display is showing something
Photograph it before it clears — codes do not wait. Search the full code list
In more detail
About Viking oven not heating
The fastest diagnosis is the code
Try each mode before you call: bake, broil and convection use different elements, and an oven that broils has already ruled out most of what could be wrong. On a double oven, note which cavity — they share a control and a supply and nothing else.
An oven that says it in English
Most makes report a number and leave you to look it up. This one puts RTD ERROR, PROBE ERROR, LATCH ERROR, KEYBOARD ERROR and MODEL ERROR on the display in words, each naming the part. It is the most direct diagnostic vocabulary in this catalog and it is worth taking at face value.
Sensor or element
They fail differently and the behavior says which. A sensor reading open leaves the control with no temperature to work from, so it will not heat at all. An element that has failed open lets the oven warm slowly, or from one direction only. Both are ordinary repairs and both are cheaper than the board people assume it must be.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards
Before you book
Questions about viking oven not heating
It broils but will not bake.
Then the broil element and the control are both fine and the bake element or its relay is not. That is genuinely good news: it is one of the cheaper repairs on this appliance.
The display says RTD ERROR.
That is the oven's own temperature sensor, open or shorted. It is a specific part, it is not expensive, and it turns up most often just after a self-clean.
Only one cavity of my double oven has stopped.
They share a control and a supply but not their elements or sensors, so this is normally a single contained repair and the other cavity keeps working.
Where we do it
Across Miami-Dade, Broward, and Palm Beach
Same terms everywhere we go: an on-site diagnostic first, the price agreed in writing, and the exact figure confirmed once we have seen the unit.
Neighborhoods people ask for by name